PreSonus R65 AMT Monitor (demo)

9.800.000₫ 8.500.000₫
VND USD

The R Series R65 AMT Monitor from PreSonus features a custom 6.8in2 Air Motion Transformer (AMT) tweeter that responds to subtle waveforms and high-frequencies.

Hết hàng


OVERVIEW

The R Series R65 AMT Monitor from PreSonus features a custom 6.8in2 Air Motion Transformer (AMT) tweeter that responds to subtle waveforms and high-frequencies. This allows you to hear the air and the greater sense of space that is characteristic of audiophile recordings. The R65's transparent and accurate sound makes it great for use in both commercial and home recording studios as well as broadcast and post-production environments.

In order to dampen resonance peaks at higher frequencies, conventional dome tweeters are injected with fluid to raise their mass, sacrificing transient response time. By contrast, the AMT tweeter in the R65 uses a thin, folded Kapton membrane (< 0.01 mm) with an inlayed aluminum circuit functioning as the voice coil, allowing the tweeter to move at the same instant as the electric current. The resulting reactive response time provides marked clarity and better transient reproduction.

Unlike a traditional 1" dome tweeter, an unfolded AMT tweeter diaphragm provides up to thirteen times the projection area.

The R65 provides a wide lateral dispersion and very limited vertical dispersion. The narrow vertical dispersion helps to reduce reflections from the ceiling and desktop that can cause phase coherence issues. The broad, even horizontal dispersion creates a wide sweet spot. Because it is less subject to room-anomaly interference, the R65 reacts more predictably and sounds more consistent from room to room.

The R65 utilizes a 6.5" custom-coated, woven Kevlar, low-frequency driver. This rigid cone maintains a more consistent dispersion pattern across its frequency response range. Biamped and driven by a 150W Class D amplifier, this monitor delivers an open, clear, and less fatiguing listening experience.

This monitor offers user-adjustable contour features for optimizing the monitor for your mixing space. This enables full integration into any studio environment. A four-position Acoustic Space switch helps to compensate for the boundary bass boost that occurs when the monitor is placed near a wall. A high-frequency driver level control helps to further mitigate room anomalies. An onboard highpass filter makes it easy to integrate a Temblor subwoofer into your monitor setup.

With three different types of audio inputs, it's easy to feed audio to your R-Series monitor from a mixer, an interface, a media player, or other line-level sources. The R65 provides balanced XLR, balanced 1/4" TRS, and unbalanced RCA line-level inputs.

Components and Construction

2-way active AMT design provides articulate high-frequency response and wide stereo imaging
Custom-designed, 6.8-inch, AMT ribbon tweeter responds to the subtle waveforms and the high-frequencies
6.5" Kevlar LF driver provides transparent mid- and low-frequency reproduction
Balanced XLR, 1/4" TRS, and an unbalanced RCA inputs provide flexibility

User Controls

Acoustic Space settings (Linear, -1.5 dB, -3 dB, -6 dB) compensate for room placement
Volume range A-type taper
HF control settings (Linear,+1, -3, -6 dB)
Low-cut settings (Linear, 60 Hz, 80 Hz, 100 Hz)

Power and Safety

Biamped 150W RMS (LF = 100W, HF = 50W), Class D power amplifier with switching power supply
RF interference, output-current limiting, over temperature, turn-on/off transient, and subsonic filter protection
Energy Conservation Mode (with enable/disable) lowers standby power to < 0.5W
External mains fuse
Internal power supply with IEC connector
Performance
Frequency Response 45 Hz to 22 kHz
Crossover Frequency 2.7 kHz
LF Amplifier Power 100 W Class D
HF Amplifier Power: 50 W Class D
SPL Peak: 104 dB
LF Driver Size 6.5" (16.51 cm) Kevlar
Driver Type HF: AMT
Diaphragm 6.8 in2
Input Impedance 20 kΩ balanced, 10 kΩ unbalanced
SNR Typical, A-Weighted: > 100 dB

 

User Controls
Volume A-type taper
Control Linear, +1 dB, -3 dB, -6 dB
High Pass Filter Linear, 60 Hz, 80 Hz, 100 Hz
Acoustic Space: linear, -1.5 dB, -3 dB, -6 dB
Mode Energy conservation: on/off/query

 

General Specifications
Inputs Balanced XLR, balanced 1/4" TRS, unbalanced RCA
Protection RF interference, output-current limiting, over-temperature, turn-on/off transient, subsonic filter, and external mains fuse
Power 100 to 120 VAC, 50/60 Hz and 220 to 240 VAC, 50/60 Hz
Standby Power < 0.5 W
Cabinet Construction Vinyl-laminated, medium-density fiberboard
Dimensions 8 x 10.3 x 13" (20.3 x 26.1 x 32.8 cm)
Weight 14.7 lb (6.65 kg)

 

Packaging Info
Package Weight 17.0 lb
Box Dimensions (LxWxH) 16.5 x 14.1 x 11.2"

 

Sale

Không sẵn có

Hết hàng